◆ What should be pa志腦id attention to when de票事bugging a precision glue dispenser光議 With the improvement of the degr他請ee of mechanical a紅熱utomation, the use of automation equi金也pment is becoming more and mor討那e extensive.

In order to better save labor costs an還睡d improve dispensing efficiency, many f上花actories have beg土照un to replace manua房開l dispensing equipme匠愛nt with automated dispensing equipm醫店ent. However, in the early stage水科 of the use of the precision glue dispe服們nser, various problems often occur算視, which need to be solved one by on南數e before continuing to use. This sit小草uation is mainly caused by the友很 failure to deb呢兵ug the precision街動 glue dispenser for the first t醫快ime.

1. Leveling It is necessary海答 to maintain the levelness of the p作好recision dispenser platform. A學唱 good level of the platform is equival廠分ent to half of the 在時debugging, which is th哥很e basis for debugging.開件 A good level of laying will a林玩void a series of dispensing problem姐刀s such as misalignment, more g見光lue and less glue, and件錯 overflowing glue.

2. Dispensing height The precision 來答dispensing machine needs to adj睡用ust the dispensing height. If歌件 the distance betw購線een the needle tip and得化 the product cup surface這場 is too high, there will be problem報店s of glue pulling; if the dispensing 校近height is too l事動ow, there will be problems such as the 拿新needle tip sticking to the glue跳道, the glue climbing, and the uneven a外光mount of product glue.

3. Needle size In 日相the dispensing 低唱process, the dispensing 那了needle needs to be sele作刀cted according to the 畫視size of the product. The inner diame吃山ter of the needle is about one-half o如微f the diameter of the glue poi兵為nt. Choosing the right needle鐵腦 can ensure the quality of 腦說the glue point and impro可唱ve the producti村媽on efficiency.

4. Setting of the glue dispensing time吧車 of the glue dispenser The amount 要票of glue to be d讀又ispensed should be h內討alf of the product spacing草門, so as to ensure suffi時友cient glue amount to paste 頻車the components and avoid e了你xcessive glue seepage. The amount of 自微glue dispensed by the precision glue ma山場chine can be controlle歌分d by adjusting the g爸人lue dispensing time. During the dispens來影ing process, the di不去spensing time can also be s月坐et according to the 志時environmental conditions (workshop t文了emperature, glue viscosity, dispensin日有g speed, etc.).

5. Pressure setting of the 森呢glue dispenser The pressure of the gl一信ue dispenser de朋要termines the amount of glue and the s機男peed of glue dispens筆用ing. High pressure is pr國爸one to problems such as內門 glue spraying and excessive glue amou木農nt, which affects the beauty of 北但the dispensing pr一時oduct; low pressure may c少話ause problems such as uneven男作 dispensing and failure to 會白dispense glue, 窗筆which directly affects 信說product quality.

In actual production, it is necessa山好ry to set the pressure according to 兒但the viscosity of劇厭 the glue, the environment o刀子f the production wor訊土kshop, and the temperature. If the tem他個perature is too low, the vi她個scosity of the glue will increa腦有se and the fluidity will become worse長作. At this time, the pre路路ssure value needs to be increa水業sed, and vice versa. For manufacturers 也明who have used automatic 玩嗎dispensing equipment for a 算站long time, after the init車用ial run-in, they have summ內放ed up the debugging experience of愛件 automatic dispensing equipm見自ent for their own products. Even if th新錯ere are occasional failures, th北光ey can be dealt with in time. However喝雜, for manufacturers who have j船裡ust started to use automatic dispens文子ing equipment, they need to analyz麗志e their products firs作暗t, determine various debugging d我嗎ata, and then try to adjust them slowly去樂.